Analogue SAT

• Frequency Band: 930–2250 MHz
• Direct selection of: memory plan, programme,
  frequency, LNB, DiSEqC, with front panel key board
• Memorization of: plan, programme, transponder, frequency, LNB, DiSEqC, local oscillator frequency
• Frequency resolution: 0,1 MHz
• Input impedance: 75 ohm
• Interchangeable input connector: “F” (“IEC” or “BNC” or “N” optional)
• Power Supply at RF input: OFF, +13, +18 V, 22 kHz (0,3 A) (with ON/OFF key)
• DiSEqC 1,1: 4, 8, 12 or 16 polarizations, DiSEqC “a.b.c.d” already pre-programmed in sequence and very easy to use. It can power any type of LNB (analogue or DiSEqC, single or dual feed) and any type of multiswitch (analogue or DiSEqCon 4, 8, 12, 16 inputs and SCR LNB)
• Analogue level measurement dynamic range at the RF input: from 35 to 120 dBuV, from –25 to + 60 dBmV (selectable) with limit indications: level Too Low, level Too High
• Measurement resolution: 0,1 dB
• Level measurement accuracy: 1.5 dB typ. (2.5 dB max.) with software correction (after 5 minutes warm-up)
• Measurement filter bandwidth in SAT mode: 4 MHz at –3 dB
• Measurement stability versus temperature between –10 and 50°C: 0,1 dB/°C
• LNB L.O. freq selection: continuous from 0 to 20.000 MHz, for “L” band (direct IF–SAT reading), “S”, “C”, “KU”, “KA”.

QPSK Demodulated

(Digital or analogue fully automatic selection also in channel navigation)

• Frequency band: 930–2250 MHz
• Direct selection of: memory plan, programme, frequency, LNB, DiSEqC, with front panel key- board
• Memorization of: plan, programme, transponder, frequency, LNB, DiSEqC, local oscillator freq, standard, symbol rate
• Frequency resolution: 0,1 MHz
• Input impedance: 75 ohm
• Interchangeable input connector: “F” (“IEC” or “BNC” or “N” optional)
• Power Supply at RF input: OFF, +13, +18 V, 22 kHz (0,3 A) (with ON/OFF key)
• DiSEqC 1,1: 4, 8, 12 or 16 polarizations, DiSEqC “a.b.c.d” already pre-programmed in sequence and very easy to use. It can power any type of LNB (analog or DiSEqC, single or dual feed) and any type of multiswitch (analogue or DiSEqC with 4, 8, 12, 16 inputs and SCR LNB)
• Digital power measurement dynamic range at RF input: from 35 to 120 typ. dBuV, from –30 to + 60 dBmV (selectable) with limit indications: level Too Low, level Too High
• Power Measurement Resolution: 0,1 dB
• Power Measurement accuracy: 1,5 dB typ. (2.5 dB max.) with software correction (after 5 minutes warm up)
• Noise Margin Measurement accuracy: 0,5 dB typ. (1 dB max) with software correction

NET. ID. and MPEG Service/Programme list

• Provides the name of the programmes (Services) the bouquet and transponder names the encryption system, orbitall position and date.

SAT Spectrum Analysis

• Frequency band: 930–2250 MHz
• Span: 50–100–200–500–FULL
• dB/div: 5
• Display dynamic range: >30 dB
• Marker measurement resolution: 0.1 dB
• Measurement filter bandwidth: 4 MHz at –3 dB
• Reference level: from 0 to 120 dBµV, from –60 dBmV to +60 dBmV
• Reference level settings: automatic and manual adjustable
• Other selectable spectrum modes:
• MAX HOLD (peak hold)
• SAT POINTING: automatic optimum setting for satellite dish alignment

Others

• Buzzer: Level or Quality according to measurement mode (with on/off Key)
• Power Supply:
• Built in rechargeable batteries: 7,2 V x 2,5 Ah (Ni–MH)
• Voltage load: 12 Vca or 12 Vcc (1 A), (connector: Ø 5,5 x 2,2)
• AC/AC adapter : 230 Vac, output: 12 Vac (supplied)
• Battery duration at 25°C: 4 hours depending on LNB consumption (9 hours optional)
• Low Battery indicator: with acoustic signalling and visual indication on graphic display and automatic meter power down
• Indication of battery status always shown on display
• Battery recharge time: 1 hour for approx 50% capacity, 3/6 hours for full charge
• Instrument size: H 80 x L 225 x D 215 mm
• Instrument weight: 1.3 kg with batteries, bag and accessories
• Casing structure: ABS plastic housing rain-dust and shock proof
• USB interface: for PC interfacing; SW up-grades, (memory plan configuration, printouts etc. optional Smart Pro S/W)
• B/W graphic display: 64 x 128 pixel
• Auto-Off timer: after 5 or 10 min without use (selectable on/off, always re-starts from last function)
• RF input overload protection: electronic, up to 60 Vac.